The European grades for the 316 and 316L types, 1.4401 and 1.4404, match on all elements with carbon ranges of 0.07% maximum for 1.4401 and 0.030% maximum for 1.4404. There are also high Mo versions (2.5% minimum Ni) of 316 and 316L in the EN system, 1.4436 and 1.4432 respectively.
EN 10088 Stainless steels - Grades/NumbersEN 10088-2:2005 Stainless steels. Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes COMPARE GRADES 1.4436 X3CrNiMo17-13-3 1.4438 X2CrNiMo18-15-4 1.4439
EN10088-2 Cold Drawn Seamless Stainless Steel TubeEN10088-2 Cold Drawn Seamless Stainless Steel Tube manufacturing by Torich International Co.--The Steel Tube Maker; Product details of China EN10088-2 Cold Drawn Seamless Stainless Steel Tube.
See the chemical composition and physical properties of EN10088-3 Grade 1.4571, find alternative materials, and connect with suppliers.
Forta 316/4401 EN 1.4401, ASTM TYPE 316H / UNS S31609 EN 10088-2:1.4401:EN 10088-3:1.4401:EN 10088-4:1.4401:IS 6911, AMENDMENT NO. 2:ISS 316; ISS 316H . Contact us. Contact us to discuss your needs in detail and request for an offer. In addition to advice on material selection we can support you in calculating design conditions.
France AFNOR 1.4436, Austenite steel, NF EN 10028-7, NF 1.4436. France AFNOR NF EN 10028-7 NF EN 10088-1 NF EN 10088-2 NF EN 10088-3 NF EN 10088-4 NF EN 10088-5 NF EN 10216-5 (2004) NF EN 10217-7 NF EN 10222-5 NF EN 10250-4 NF EN 10253-3 NF EN 10253-4 NF EN 10263-5 NF EN 10272 NF EN 10296-2 (2005) NF EN 10297-2 (2005) 1.4436 Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2
Stainless Steel Grade 1.4436; Stainless Steel Grade 1.4436; Stainless Steel Grade 1.4438; Stainless Steel Grade EN 10088-2; Reliable Steel Distributors. Email. [email protected] Phone. 022 42132900 (100 Lines)
Stainless Steel - General Information - EN Standards for Finishes According to BS EN 10088-2 / 10028-7 *NOTE:Special finishes indicate hot rolled (1) and cold rolled (2) sheets, e.g.:Ground polished hot rolled sheets + 1G / Ground polished cold rolled sheets = 2G For more information on stainless steel finishes please
Stainless Steel 316 Sheets, SS TP 316L Plates Exporter Stainless Steel 316/316L Sheets, Plates & Coils Specification. Standard ASTM A240 / ASME SA240, JIS4304-2005, ASTM A167, EN10088-2-2005, GB/T3280-2007, etc. Range 0.5 mm To 150 mm thick in 1000 mm TO 2000 mm width & 2500 mm to 6000 mm Length available with NACE MR 01-75.. Surface Finishing Hot rolled plate (HR), Cold rolled sheet (CR),2B, 2D, BA, NO.1, NO.4, NO.8, 8K, mirror,
EN 1.4404, 1.4432 or 1.4436 but in common with these grades 1.4462 is alloyed with molybdenum. The steel is also alloyed with nitrogen. The yield strength of 1.4462 is about double that of the austenitic steels mentioned. Flat formats of 1.4462 are standardised in EN 10088-2.
Stainless Steel:Tables of Technical Properties Chemical and physical properties are in accordance with EN 10088-1:2005 Mechanical properties are in accordanc e with EN 10088-2:2005, except for he at resisting grad es (EN 100 95:1999) 0,11 16,50 to 18,50 2,00 to 2,50 10,00 to 13,00 X3CrNiMo17-13-3 1.4436 316
UK B.S. 1.4436, Austenite steel, BS EN 10028-7, BS EN 1.4436. UK B.S. BS EN 10028-7 BS EN 10088-1 BS EN 10088-2 BS EN 10088-3 BS EN 10088-4 BS EN 10088-5 BS EN 10216-5 (2004) BS EN 10217-7 BS EN 10222-5 BS EN 10250-4 BS EN 10253-3 BS EN 10253-4 BS EN 10263-5 BS EN 10272 BS EN 10296-2 (2005) BS EN 10297-2 (2005) 1.4436 Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2
Chemical composition % of steel X3CrNiMo17-13-3 (1.4436):EN 10088-2-2005 Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0.015 % to 0.030% is recommended and permitted.X3CrNiMo17-13-3 / 1.4436 - SteelNumber - Chemical Chemical composition % of steel X3CrNiMo17-13-3 (1.4436):EN 10088-2-2005 Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0.015 % to 0.030% is recommended and permitted.